tag:blogger.com,1999:blog-8006771064878274469.post7697751473447251228..comments2024-03-23T19:50:21.420-05:00Comments on Tektonten Papercraft: Space 1999 Papercraft: Eagle TransporterTektontenhttp://www.blogger.com/profile/14309447916511397471noreply@blogger.comBlogger8125tag:blogger.com,1999:blog-8006771064878274469.post-83765142036707067662023-03-30T10:46:32.869-05:002023-03-30T10:46:32.869-05:00Thanks for taking the time to do this!Thanks for taking the time to do this!Tektontenhttps://www.blogger.com/profile/14309447916511397471noreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-72086989085435585842023-03-25T01:27:00.914-05:002023-03-25T01:27:00.914-05:00Sheet1
1) X marked the inner part of the shock abs...Sheet1<br />1) X marked the inner part of the shock absorbers.<br />2) Elongated the altitude thrusters, making it easier to properly roll them.<br /> I am experimenting with a conical design<br />3) elongated the support beam. With current version, it was not reaching both side of the pods<br />4) Secondary gear struts: Added the inner side, so both sides will be black. It gives a better strenght to the piece as well <br /><br /> Sheet2<br />1) X marked the support beam hole<br /> Sheet3<br />1) Detached the right side door panel, making it clearer what has to be cut<br /> Sheet4<br />1) simply marked what to cut and what to fold<br /> Sheet5<br />1) Adjust position of cockpit window, making it clearer how to asemble<br />2) Build the join based on the engine's belt.<br /> Started to work on another type of join,<br /> where the commander module back will be closed with a panel holding a door and 4 little atatches<br />3) simply marked what to cut<br />4) made the steering thrusters smaller (85% from original) as to match the size of the placeholder<br /> Sheet6a<br />1) added tab on the grey inner big bell<br />2) added tabs on the engine's cover part. Spaced them a bit as to ease the cutting<br />3) removed some ghost pixels on the upper part of the engine's central piece<br /> Sheet6b<br />1) Doubled the engine's connector. So both sides are offering the same image. It gives a better strenght to the piece as well <br />2) (todo) added tabs on the engine's cover part. Spaced them a bit as to ease the cuttingSheet7<br />Lift off thrusters<br />Created the sheet using the small engine bell<br />There are two dimensions, since the forward and aft frames have less space than the passenger module to install them<br />Not finished yetAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-72497959685834361762023-03-25T01:26:23.925-05:002023-03-25T01:26:23.925-05:00These are partial written instructions by a fellow...These are partial written instructions by a fellow that built the model on his own. They might help a bit. I've got to sketch out some usable instructions asap.<br />Sheet1<br />1) X marked the inner part of the shock absorbers.<br />2) Elongated the altitude thrusters, making it easier to properly roll them.<br /> I am experimenting with a conical design<br />3) elongated the support beam. With current version, it was not reaching both side of the pods<br />4) Secondary gear struts: Added the inner side, so both sides will be black. It gives a better strenght to the piece as well <br /><br /> Sheet2<br />1) X marked the support beam hole<br /> Sheet3<br />1) Detached the right side door panel, making it clearer what has to be cut<br /> Sheet4<br />1) simply marked what to cut and what to fold<br /> Sheet5<br />1) Adjust position of cockpit window, making it clearer how to asemble<br />2) Build the join based on the engine's belt.<br /> Started to work on another type of join,<br /> where the commander module back will be closed with a panel holding a door and 4 little atatches<br />3) simply marked what to cut<br />4) made the steering thrusters smaller (85% from original) as to match the size of the placeholder<br /> Sheet6a<br />1) added tab on the grey inner big bell<br />2) added tabs on the engine's cover part. Spaced them a bit as to ease the cutting<br />3) removed some ghost pixels on the upper part of the engine's central piece<br /> Sheet6b<br />1) Doubled the engine's connector. So both sides are offering the same image. It gives a better strenght to the piece as well <br />2) (todo) added tabs on the engine's cover part. Spaced them a bit as to ease the cuttingSheet7<br />Lift off thrusters<br />Created the sheet using the small engine bell<br />There are two dimensions, since the forward and aft frames have less space than the passenger module to install them<br />Not finished yetAdrian m. Kleinbergennoreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-88613208421644121602021-09-07T08:32:51.576-05:002021-09-07T08:32:51.576-05:00Maybe you need to create a DeviantART login?Maybe you need to create a DeviantART login?Tektontenhttps://www.blogger.com/profile/14309447916511397471noreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-36097846066149163782021-09-05T20:10:28.032-05:002021-09-05T20:10:28.032-05:00why cant i download the space 1999 eagle modelwhy cant i download the space 1999 eagle modelAnonymoushttps://www.blogger.com/profile/13778987324297239629noreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-2101685733862095122020-05-03T12:40:50.492-05:002020-05-03T12:40:50.492-05:00Sorry the designer did not provide any instruction...Sorry the designer did not provide any instructions. However he does provide some additional photos which you may find helpful: https://www.deviantart.com/frohickey/art/Eagle-Card-Model-2-203451687Tektontenhttps://www.blogger.com/profile/14309447916511397471noreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-51350074094263619812020-05-03T12:11:14.020-05:002020-05-03T12:11:14.020-05:00Could use a set of instructions, some pictures do ...Could use a set of instructions, some pictures do not reflect the actual pringoutsOldElvishttps://www.blogger.com/profile/11244242760329999923noreply@blogger.comtag:blogger.com,1999:blog-8006771064878274469.post-71428953751332187152012-05-12T21:16:21.232-05:002012-05-12T21:16:21.232-05:00MARVELOUS!
THANKS...
RODO MEDINA - COLOMBIAMARVELOUS!<br />THANKS...<br /><br />RODO MEDINA - COLOMBIAAnonymousnoreply@blogger.com